PulseGuard Pulsation Dampers
PulseGuard: Guarding Against Pulsation
Pump Pulsation Dampers
Fluid Flow Control Animations

Pulsation Damper Information PDF Page PG65 & PG66 Pulsation Damper Weights and Dimensions Printable Version
Pulsation Damper Site - Arrow Drawings below

Pulsation Dampers For Flow Smoothing and Pressure Pulse Interception

Pulsation Dampers In Dual Use Configuration,
For Flow Smoothing AND Pressure Pulse Interception, by multi connection Thru-Flow.

High Pressure Pulsation DampersPulseGuard Pulsation Dampers

Due to the instability of metal prices, please call the factory for pulsation damper prices.

To use any damper rated above 370 Bar / 5,350 psi at a greater pressure, please add 98 to list price, and specify Pre-Fill Valve Nbr. "8M-28 f/ss, for uses up to 750 Bar / 10,800 psi.
PART NUMBER LETTERING ABBREVIATIONS: "TW" - Twin Connection, is replaced by "FF - for a single Flange Face (no extra charge). "+ Flg". a flange that is larger than the Damper. welded on (at extra charge). "O" denotes "O" ring face (no charge), matches a bolt on piping base block ("+PB"). Model Nbr. preceded by "U" = an ASME "U" stamped damper. OR "CE" where pressure times volume of liquid danger causes the EU Pressure Equip Directive category. Prefix "JKT" denotes hot or cold jacket.
WETTED PARTS MATERIAL DESIGNATIONS: Replace the "Ss" in the part nbr. As follows, "DSS" - Duplex Stainless (2205, F-51, UNS S31803), SDSS - Super Duplex (2507, UNS S32750), A20 - Alloy 20, T2 - Titanium 2, H22 - Hasteloy 22, HC 276 - Gr. C276, H2 - Gr B2. Tan - Tantalum.
CONNECTION Abbreviations: - "F" - Female, M - Male, B- BSP/ ISO straight thread, N - NPT, TD - Single Thread, W - Weld Prep 37.5 Degree, SO - Socket for welding your pipe into.
("NB") - Note Bene - Design Pressure "DP" at temperature, will vary by allowable stress for other than dual certified 316/316L "Ss" material. Design Pressure may be MAWP +10% for RV set pressure. Then + 15% for RV accumulation. Hence MAWP may be D.P. times 0.79. Alternately MAWP may be DP at the discretion of the end user (according to the "ASME" who take no responsibility).
DIN 2501 "DN--PN--" flanges may imply the use of European Pressure Vessel codes. Be aware that they use higher allowable working stresses, so may be less safe than our 30 year proven standard, which has ensured no fatigue failure from strain fluctuation in this cyclic stress application.


Pulsation Dampers Installed Correctly Increase Performance

YOUR OPTIONS THAT GREATLY REDUCE THE PIPING INSTALLATION COST FOR YOU
Pulsation Damper - Single Connection PipeHugger
Pulsation Damper - Single Connection PipeHugger
Pulsation Damper - Single Connection PipeHugger
Pulsation Damper - PipeHugger with Piping Base
Pulsation Damper - PipeHugger with Piping Base
Pulsation Damper - PipeHugger with Piping Base
Pulsation Damper - Minimum Down Time PipeHugger
Pulsation Damper - Minimum Down Time PipeHugger
Pulsation Damper - Minimum Down Time PipeHugger

PipeHugger HP is also ideal for flurries and suspended particulate, because the bladder is constantly shaking it free, unlike "gas bags" which pack it against the vessel wall.

 



nba jerseys australia wholesale makeup cheap nfl jerseys replica sunglasses outlet uk
 Pulsation Damper Distributors
Low Pressure PTFE Membrane Types High Pressure PTFE Diaphragm Dampers Bladder Accumulators / Pulsation Dampeners Elastomer Bladder Dampers / PipeHugger Low Pressure Elastomer Bladder Damper / PipeHugger High Pressure Flow Through Flexible Tubes / PumpGuard
PulseGuard
PulseGuard Pulsation Dampers
International: --44 (0) 161-480-9625
UK Free Phone: 08080 LO-PRICE (56-77423)
Email: PG.Stabilizers.Sales.UK@Gmail.com
Pulsation Dampers | Pulse Damper Drawings
PulseGuard Pump Pulsation Dampers PulseGuard Pulsation Dampers PulseGuard Ltd. Pulsation Dampers Dampners from stock, for United Kingdom - Europe - and Asia

Copyright © 2017 PulseGuard. | PulseGuard is the UK trademark of PulseGuard Limited and the US trademark of PulseGuard Inc..